Single Position Tool Holder


Single Position Tool Holder

Add Your Review
Availability: In Stock
Product SKU: TBS-1356
Prop 65
Warning

This product can expose you to chemicals, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information on this product, please refer to the SDS file. For more information on Prop 65, please visit www.p65warnings.ca.gov.

$0.00
This single position tool holder allows you to create a custom set up to accommodate any job. Allows spacing tools of varying lengths, so as not to hit the collet when using a shorter tool. Offset bore provides clearance for use with OD insert turning bar. RH = bore to the right when facing spindle; LH = bore to the left (as shown in photo).

Smaller width to save space in the X axis. Differential spacing of the holes in each holder allow different tool configurations for narrow and wide spaced tools on one block. An end stop mounted to the table provides repeatable location of the tool block for quick changeover of setups.

Order # Description A B C
TBS-1356

3/8” Center, 5/8” Bore, RH

 .3750 .6250 1.500
TBS-1357 3/8” Center, 5/8” Bore, LH .3750 .6250 1.500
TBS-1456 1/2” Center, 5/8” Bore, RH .5000 .6250 1.500
TBS-1457 1/2” Center, 5/8” Bore, LH .5000 .6250 1.500
TBS-1466 1/2” Center, 3/4” Bore, RH .5000 .7500 1.500

GTH-1204LH

(TBS-1467)

 1/2” Center, 3/4” Bore, LH .5000 .7500 1.500
TBS-1426 1/2” Center, 20mm Bore, RH .5000 20mm 1.500
TBS-1427 1/2” Center, 20mm Bore, LH .5000 20mm 1.500
TBS-1666*
 3/4” Center, 3/4” Bore, RH .7500 .7500 1.500
TBS-1667 3/4” Center, 3/4” Bore, LH .7500 .7500 1.500
TBS-1626 3/4" Center, 20mm Bore, RH .7500 20mm 1.500
TBS-1627 3/4" Center, 20mm Bore, LH .7500 20mm 1.500


*Temporarily unavailable, please contact us for additional information.

ECI ceased operations in July of 2021. All remaining ECI stock is no longer available once sold. ARTCO has begun producing replacement tool holders as ECI stock is depleted. These new part numbers for the Single Position Tool Holders now begin with "GTH" rather than the previous "TBS." If you are looking for a particular dimension tool holder please do not hesitate to reach out to us regarding availability.

This single position tool holder allows you to create a custom set up to accommodate any job. Allows spacing tools of varying lengths, so as not to hit the collet when using a shorter tool. Offset bore provides clearance for use with OD insert turning bar. RH = bore to the right when facing spindle; LH = bore to the left (as shown in photo).

Smaller width to save space in the X axis. Differential spacing of the holes in each holder allow different tool configurations for narrow and wide spaced tools on one block. An end stop mounted to the table provides repeatable location of the tool block for quick changeover of setups.
Order # Description A B C
TBS-1356

3/8” Center, 5/8” Bore, RH

 .3750 .6250 1.500
TBS-1357 3/8” Center, 5/8” Bore, LH .3750 .6250 1.500
TBS-1456 1/2” Center, 5/8” Bore, RH .5000 .6250 1.500
TBS-1457 1/2” Center, 5/8” Bore, LH .5000 .6250 1.500
TBS-1466 1/2” Center, 3/4” Bore, RH .5000 .7500 1.500

GTH-1204LH

(TBS-1467)

 1/2” Center, 3/4” Bore, LH .5000 .7500 1.500
TBS-1426 1/2” Center, 20mm Bore, RH .5000 20mm 1.500
TBS-1427 1/2” Center, 20mm Bore, LH .5000 20mm 1.500
TBS-1666* 3/4” Center, 3/4” Bore, RH .7500 .7500 1.500
TBS-1667 3/4” Center, 3/4” Bore, LH .7500 .7500 1.500
TBS-1626 3/4" Center, 20mm Bore, RH .7500 20mm 1.500
TBS-1627 3/4" Center, 20mm Bore, LH .7500 20mm 1.500


*Temporarily unavailable, please contact us for additional information.

ECI ceased operations in July of 2021. All remaining ECI stock is no longer available once sold. ARTCO has begun producing replacement tool holders as ECI stock is depleted. These new part numbers for the Single Position Tool Holders now begin with "GTH" rather than the previous "TBS." If you are looking for a particular dimension tool holder please do not hesitate to reach out to us regarding availability.